Briefly, this error occurs when a node in Elasticsearch cluster is shutting down and it rejects the master failure notification. This could be due to network issues, heavy load, or a slow cluster. To resolve this, you can check the node’s logs for any shutdown signals. If the node is overloaded, consider optimizing your queries or adding more nodes to the cluster. If it’s a network issue, ensure stable connectivity between nodes. Also, ensure your cluster health is green and all nodes are properly connected.
This guide will help you check for common problems that cause the log ” master failure notification was rejected; it’s highly likely the node is shutting down ” to appear. To understand the issues related to this log, read the explanation below about the following Elasticsearch concepts: master, node, discovery.
Overview
To put it simply, a node is a single server that is part of a cluster. Each node is assigned one or more roles, which describe the node’s responsibility and operations. Data nodes store the data, and participate in the cluster’s indexing and search capabilities, while master nodes are responsible for managing the cluster’s activities and storing the cluster state, including the metadata.
While it is possible to run several node instances of Elasticsearch on the same hardware, it’s considered a best practice to limit a server to a single running instance of Elasticsearch.
Nodes connect to each other and form a cluster by using a discovery method.
Roles
Master node
Master nodes are in charge of cluster-wide settings and changes – deleting or creating indices and fields, adding or removing nodes and allocating shards to nodes. Each cluster has a single master node that is elected from the master eligible nodes using a distributed consensus algorithm and is reelected if the current master node fails.
Coordinating (client) node
There is some confusion in the use of coordinating node terminology. Client nodes were removed from Elasticsearch after version 2.4 and became coordinating nodes.
Coordinating nodes are nodes that do not hold any configured role. They don’t hold data and are not part of the master eligible group nor execute ingest pipelines. Coordinating nodes serve incoming search requests and act as the query coordinator running query and fetch phases, sending requests to every node that holds a shard being queried. The coordinating node also distributes bulk indexing operations and route queries to shards based on the node’s responsiveness.
Overview
The process known as discovery occurs when an Elasticsearch node starts, restarts or loses contact with the master node for any reason. In those cases, the node needs to contact other nodes in the cluster to find any existing master node or initiate the election of a new master node.
How it works
Upon startup, each node looks for other nodes, firstly by contacting the IP addresses of eligible master nodes held in the previous cluster state. If they are not available, it will look for nodes based upon the seed host provider mechanisms available.
Seed host providers may be defined in 3 ways: list based, file based or plugin based. All of these methods provide a list of IP addresses or hostnames which the node should contact in order to obtain a list of master eligible nodes. The node will contact all of these addresses in turn, until either an active master is found, or failing that, until sufficient nodes can be found to elect a new master node.
Examples
The simplest form is to define a list of seed host providers in elasticsearch.yml:
discovery.seed_hosts: - 192.168.1.10:9300 - 192.168.1.11 - seeds.mydomain.com
An alternative way is to refer to a file using the following setting:
discovery.seed_providers: file
The file MUST be placed in the following filepath: $ES_PATH_CONF/unicast_hosts.txt
10.10.10.5 10.10.10.6:9305 10.10.10.5:10005 # an IPv6 address [2001:0db8:85a3:0000:0000:8a2e:0370:7334]:9301
Note that the use of a port is optional. If not used, then the default port range of 9300-9400 will be used.
If you use AWS or GCS then you can install and use a plugin to obtain a list of seed hosts from an API. A plugin also exists for Azure but is deprecated since version 5.
AWS plugin
A typical configuration could be as follows:
discovery.seed_providers: ec2 discovery.ec2.tag.role: master discovery.ec2.tag.environment: dev discovery.ec2.endpoint: ec2.us-east-1.amazonaws.com cloud.node.auto_attributes: true cluster.routing.allocation.awareness.attributes: aws_availability_zone
The above configuration would look for all nodes with a tag called “environment” set to “dev” and a tag called “role” set to “master”, in the AWS zone us-east-1. The last two lines set up cluster routing allocation awareness based upon aws availability zones. (Not necessary, but nice to have).
GCE plugin
A typical configuration could be as follows:
discovery.seed_providers: gce cloud.gce.project_id: <your-google-project-id> cloud.gce.zone: <your-zone> discovery.gce.tags: <my-tag-name>
The above configuration would look for all virtual machines inside your project, zone and with a tag set to the tag name you provide.
Notes and good things to know
Cluster formation depends on correct setup of the network.host settings in elasticsearch.yml. Make sure that the nodes can reach each other across the network using their IP addresses / hostname, and are not getting blocked due to firewall settings on the ports required.
Log Context
Log “master failure notification was rejected; it’s highly likely the node is shutting down” classname is MasterFaultDetection.java.
We extracted the following from Elasticsearch source code for those seeking an in-depth context :
for (Listener listener : listeners) {
listener.onMasterFailure(masterNode; cause; reason);
}
});
} catch (EsRejectedExecutionException e) {
logger.error("master failure notification was rejected; it's highly likely the node is shutting down"; e);
}
stop("master failure; " + reason);
}
}
[ratemypost]
